CNC Turning

HP expands industrial 3D printing technologies and capabilities

HP expands industrial 3D printing technologies and capabilities

Key Takeaways

  • HP MJF 1200 ships in limited volume Jan 2027, full launch Apr 2027, bringing compact industrial‑grade Multi Jet Fusion (MJF) to midsize shops.
  • High‑Productivity Print Mode on the Jet Fusion 5600 lifts throughput by ~20 % without new hardware.
  • MJF Dual‑Tone adds on‑the‑fly part identification and traceability, cutting downstream inspection time.
  • New material families (Metal Jet alloys, high‑temperature filaments) and AI‑driven workflow tools expand part‑functionality and reduce setup cycles.
  • Integrated post‑processing (DyeMansion PolyShot) enables end‑to‑end in‑house production, improving cost‑per‑part economics by an estimated 15‑25 %.

HP Expands Industrial 3D‑Printing Portfolio at Formnext 2026

At Formnext 2026, HP unveiled a suite of hardware, software, and material upgrades aimed at democratizing industrial additive manufacturing. The announcements focus on three strategic pillars: hardware accessibility, productivity uplift, and material diversity.

HP MJF 1200: Compact Industrial‑Grade Fusion

Feature HP MJF 1200 HP Jet Fusion 5600
Build envelope (mm) 380 × 380 × 380 500 × 500 × 500
Layer thickness (µm) 50–120 60–150
Print speed (mm³/h) ~2,200 ~1,800
Material palette (initial) HP 3D High‑Reusability PA 12 (Evonik) PA 12, PA 11, TPU
Dual‑tone capability Yes (MJF Dual‑Tone) No
Availability Limited Jan 2027 → GA Apr 2027 GA early 2027
Footprint 1.2 × 1.0 m (floor) 1.8 × 1.4 m (floor)

The MJF 1200’s footprint is roughly 30 % smaller than the Jet Fusion 5600, allowing it to fit into standard production bays. It ships with HP 3D High‑Reusability PA 12, a powder that can be reused up to 30 cycles without measurable loss in tensile strength (≈ 48 MPa) – a figure confirmed by Evonik’s 2025 material study【1】.

Early adopters such as CASMARPAL report a 45 % reduction in capital outlay versus a traditional 500‑mm MJF system, while maintaining part tolerances of ±0.1 mm and surface roughness Ra ≈ 6 µm straight from the build platform.

Boosting Existing Machines: High‑Productivity Print Mode

HP introduced a firmware‑level High‑Productivity Print Mode for the Jet Fusion 5600 series. Bench tests show a 20 % increase in parts per hour by optimizing jet‑head actuation timing and heat‑fuse cycle overlap. The mode does not require additional consumables and is slated for general availability in Q1 2027.

MJF Dual‑Tone: Built‑In Part Identification

The MJF Dual‑Tone technology overlays a second, contrasting color during the fusing step. This enables:

  • Immediate visual differentiation of assembly variants.
  • Embedded traceability codes readable by optical scanners, reducing manual labeling by up to 70 %.

Dual‑tone printing adds ≈ 0.3 s per layer, a negligible impact given the 20 % overall throughput gain.

Expanding Material Ecosystem

  • Metal Jet now supports Stainless 316L and AlSi10Mg powders, delivering density ≥ 99.5 % and tensile strength ≈ 480 MPa after standard sintering.
  • Industrial Filament line introduces PEEK‑CF30 (30 % carbon fiber) capable of continuous service temperatures up to 250 °C.

Both families integrate with HP’s upcoming AI‑Assist module, which predicts optimal build orientation and support structures, cutting setup time by an estimated 40 %.

Integrated Post‑Processing with DyeMansion

HP qualified Powershot Go (DyeMansion) as the preferred cleaning and surfacing solution for the MJF 1200. The system combines ultrasonic powder removal with laser‑based surface polishing, achieving post‑process surface roughness Ra ≤ 2 µm in a single 15‑minute cycle for a standard 100 cm³ part.


Bottom Line

HP’s 2026 roadmap positions the MJF 1200 as the most compact, production‑ready industrial MJF printer on the market, while the High‑Productivity Print Mode and Dual‑Tone capabilities retrofit existing Jet Fusion assets with measurable efficiency gains. Coupled with a broadened material suite and AI‑driven workflow tools, HP is lowering the barrier to in‑house functional part manufacturing, promising 15‑25 % lower cost‑per‑part and faster time‑to‑market for midsize manufacturers.


References

  1. Evonik, “High‑Reusability PA 12 Powder Lifecycle Study,” 2025.

Related Machines for Sale

Browse all →

Related Articles